How to adjust the timing of memory stick c19
作者：布仲基 | 发布日期：2024-09-21 20:15:36
本文目录一览
1. The frequencies of these two memories are the same, so it is recommended to choose the memory with CL=17.
2. No. According to Baidu Encyclopedia, the lower the timing of the memory module, the better the overclocking potential. High-timing memory has good stability at high frequencies. High-end memory modules use relatively low timing. The 19 timing bar is neither high nor low, so the memory of 19 timing is not the worst.
3. It looks very different. I got used to using the 2 and then bought a 19. When I looked at it, I thought it was very small. After using a friend's 2, I looked back and saw that the 22 was much smaller. Recommended 19 inches. The key is that the 19-inch display can display a much higher resolution than the 17-inch display. As a monitor, between 19-22 is the best choice. 22 is better for games and movies.
4.: 10) The area should be large. The poster can point to the width. I feel that the width of a 17-inch widescreen monitor and a 19-inch regular screen monitor should be relatively close. Therefore, when watching a movie with a 16:9 ratio, the visual feeling of the two is similar. However, if you are watching a traditional A 4:3 full-screen movie is much larger than 19 inches.
5. Then look at the frequency 320030002800266624002133. I only look at the timing at the end, and I can’t say whether smaller is better or bigger is better. There will be different answers depending on the reason for use. But generally the smaller the city, the better.
6. Usually the value of tRFC cannot reach 9, while 10 is the optimal setting, and 17-19 is the recommended value for memory overclocking. It is recommended to test this value starting from 17 and decreasing in sequence. Most stable values are tRC plus 2-4 clock cycles.
Kefu cjr general article, does the timing c19.19.19 overclocking increase the timing, or pull it down?
The best timing of cjr3600 memory: 3733's 16-20-20 than 3600 The 16-18-18 good memory timing is four parameters that describe the performance of synchronous dynamic random access memory (SDRAM): CL, TRCD, TRP and TRAS, in clock cycles.
Under the same frequency, the lower the timing, the better, so it is better to choose Inruida Platinum. However, for this kind of memory, the difference in timing is not very big.
The timing of the memory at silent frequency 2400MHz is 17-17-17-39, the voltage is 2V, and the results are similar. AIDA memory and cache test, memory voltage 4V, silent frequency 2400MHz, timing 17-17-17-39 test results: read 36204MB/s, write 35791MB/s, copy 33054MB/s, delay 87ns.
Press the DEL key to enter the BIOS when the computer is just turned on. You can see the CMOS main menu and the overclocking options are in the "PowerUserOverclockSettings" option. Press the enter key to enter the "PowerUserOverclockSettings" option to set parameters.
It has some relationship with SK Hynix, but it is not the actual son of SK Hynix as reported on the Internet, but a partnership with the SK Group. Most of the memory chips under this brand are made by SK Hynix, and the overall quality is quite good. The CJR particles used in some common strips are very cost-effective for overclocking users.
There are three types of granules with high cost performance, from low to high: Hynix CJR, the repre sentative product is Kefu Pu strip 2666, which can probably exceed 3800~3900MHz, the cheapest price (the same price as the Pu strip) The best value for money. Hynix DJR, the mainstream product is Kefu Thunder, which is above 4000MHz and the timing is slightly slower.
- What does memory c14c15c16 refer to? Is it timing?
- Is there a big difference between timing 17 and 19?
- Kefu cjr general article, does the timing c19.19.19 overclocking increase the timing, or pull it down?
If it is used for general purposes, there is not much difference between the two. The timing of C9 and C11 is different. Both can be overclocked, but they need to be set in the BIOS. Automatic overclocking is required. The motherboard comes with built-in support.
1. The frequencies of these two memories are the same, so it is recommended to choose the memory with CL=17.
2. No. According to Baidu Encyclopedia, the lower the timing of the memory module, the better the overclocking potential. High-timing memory has good stability at high frequencies. High-end memory modules use relatively low timing. The 19 timing bar is neither high nor low, so the memory of 19 timing is not the worst.
3. It looks very different. I got used to using the 2 and then bought a 19. When I looked at it, I thought it was very small. After using a friend's 2, I looked back and saw that the 22 was much smaller. Recommended 19 inches. The key is that the 19-inch display can display a much higher resolution than the 17-inch display. As a monitor, between 19-22 is the best choice. 22 is better for games and movies.
4.: 10) The area should be large. The poster can point to the width. I feel that the width of a 17-inch widescreen monitor and a 19-inch regular screen monitor should be relatively close. Therefore, when watching a movie with a 16:9 ratio, the visual feeling of the two is similar. However, if you are watching a traditional A 4:3 full-screen movie is much larger than 19 inches.
5. Then look at the frequency 320030002800266624002133. I only look at the timing at the end, and I can’t say whether smaller is better or bigger is better. There will be different answers depending on the reason for use. But generally the smaller the city, the better.
6. Usually the value of tRFC cannot reach 9, while 10 is the optimal setting, and 17-19 is the recommended value for memory overclocking. It is recommended to test this value starting from 17 and decreasing in sequence. Most stable values are tRC plus 2-4 clock cycles.
The best timing of cjr3600 memory: 3733's 16-20-20 than 3600 The 16-18-18 good memory timing is four parameters that describe the performance of synchronous dynamic random access memory (SDRAM): CL, TRCD, TRP and TRAS, in clock cycles.
Under the same frequency, the lower the timing, the better, so it is better to choose Inruida Platinum. However, for this kind of memory, the difference in timing is not very big.
The timing of the memory at silent frequency 2400MHz is 17-17-17-39, the voltage is 2V, and the results are similar. AIDA memory and cache test, memory voltage 4V, silent frequency 2400MHz, timing 17-17-17-39 test results: read 36204MB/s, write 35791MB/s, copy 33054MB/s, delay 87ns.
Press the DEL key to enter the BIOS when the computer is just turned on. You can see the CMOS main menu and the overclocking options are in the "PowerUserOverclockSettings" option. Press the enter key to enter the "PowerUserOverclockSettings" option to set parameters.
It has some relationship with SK Hynix, but it is not the actual son of SK Hynix as reported on the Internet, but a partnership with the SK Group. Most of the memory chips under this brand are made by SK Hynix, and the overall quality is quite good. The CJR particles used in some common strips are very cost-effective for overclocking users.
There are three types of granules with high cost performance, from low to high: Hynix CJR, the repre sentative product is Kefu Pu strip 2666, which can probably exceed 3800~3900MHz, the cheapest price (the same price as the Pu strip) The best value for money. Hynix DJR, the mainstream product is Kefu Thunder, which is above 4000MHz and the timing is slightly slower.
